;
; This is supplied as a sample only. Edit with your own data and formulas as required.
;
; Edit the values and bend equations as required.
; Use 'File - Save As Text' to create an ASCII bend table file
; 
;-----------------------------------------------------------------------
;
;  Notations used in tables:
;
;  
;  ';' = remark character
;
;  '*' = start of a new table
;
;  '/' = special character
;                             U = units of tolerance; thickness; bend radius; and correction values
;                                   m; cm; mm; micron; inch; ft;or yd
;                             S = sheet thickness
;                             R = bending radii
;                             A = opening angle 
;                            T1 = Tolerance (+/-) for sheet thickness S (valid for the whole file)
;                            T2 = tolerance for equal min and max bending radius R 
;                                 The T2 tolerance is only utilized at the minimum and maximum
;                                 bending radii R in the tables.  For model bend radii that fall
;                                 between two values existing in the table; the resultant 
;                                 correction value X is determined by linear interpolation
;                                 using the appropriate x values in the table.
;                            T3 = tolerance for equal min and max opening angle A 
;                                 The T3 tolerance is only utilized at the minimum and maximum
;                                 opening angles A in the tables.  For model opening angles
;                                 that fall between two values existing in the table; the
;                                 resultant correction value X is determined by linear 
;                                 interpolation using the appropriate X values in the table.
;
;-----------------------------------------------------------------------
;
;  The correction value X is applied as follows:
;
;  L = A + B - x
;  
;  (L = unfolded length in flat pattern)
;  (A = length of side A (outside measurement of bendingzone))
;  (B = length of side B (outside measurement of bendingzone))
;
;-----------------------------------------------------------------------
;
; Angle A expressed in degrees.  
;	
;-----------------------------------------------------------------------	
;	
;	
;UNITS for tolerance; thickness; bend radius and correction values	
; use Autodesk Inventor standard units such as 'in' and 'mm'	
/U	in
;	
;TOLERANCES valid for the whole file	
;	
/T1	0.000040
/T2	0.004000
/T3	0.004000
;	
;	
*** TABLE 1	
;										
;sheet thickness										
/S	0.060000									
;										
;bending radii										
/R		0.015000	0.031250	0.062500	0.093750	0.125000	0.156250	0.187500	0.218750	0.250000
;opening angle: ------------------------ correction value x ----------										
/A	0.000000	0.069986	0.036414	-0.013446	-0.057419	-0.098981	-0.139223	-0.178629	-0.217459	-0.255866
/A	1.000000	0.070431	0.037226	-0.012010	-0.055392	-0.096376	-0.136047	-0.174887	-0.213153	-0.251000
/A	5.000000	0.072209	0.040472	-0.006267	-0.047282	-0.085954	-0.123342	-0.159917	-0.195932	-0.231536
/A	10.000000	0.074432	0.044530	0.000912	-0.037146	-0.072927	-0.107460	-0.141205	-0.174405	-0.207207
/A	15.000000	0.076654	0.048588	0.008091	-0.027009	-0.059900	-0.091579	-0.122493	-0.152879	-0.182877
/A	20.000000	0.078877	0.052646	0.015270	-0.016872	-0.046872	-0.075698	-0.103781	-0.131352	-0.158548
/A	25.000000	0.081099	0.056704	0.022449	-0.006736	-0.033845	-0.059817	-0.085069	-0.109825	-0.134218
/A	30.000000	0.083322	0.060762	0.029628	0.003401	-0.020818	-0.043936	-0.066357	-0.088299	-0.109888
/A	35.000000	0.085545	0.064820	0.036807	0.013538	-0.007790	-0.028055	-0.047646	-0.066772	-0.085559
/A	40.000000	0.087767	0.068878	0.043986	0.023674	0.005237	-0.012173	-0.028934	-0.045246	-0.061229
/A	45.000000	0.089990	0.072936	0.051165	0.033811	0.018264	0.003708	-0.010222	-0.023719	-0.036900
/A	50.000000	0.092212	0.076994	0.058345	0.043947	0.031291	0.019589	0.008490	-0.002192	-0.012570
/A	55.000000	0.094435	0.081052	0.065524	0.054084	0.044319	0.035470	0.027202	0.019334	0.011760
/A	60.000000	0.096658	0.085110	0.072703	0.064221	0.057346	0.051351	0.045914	0.040861	0.036089
/A	65.000000	0.098880	0.089168	0.079882	0.074357	0.070373	0.067233	0.064626	0.062388	0.060419
/A	70.000000	0.101103	0.093225	0.087061	0.084494	0.083400	0.083114	0.083338	0.083914	0.084749
/A	75.000000	0.103325	0.097283	0.094240	0.094631	0.096428	0.098995	0.102050	0.105441	0.109078
/A	80.000000	0.105548	0.101341	0.101419	0.104767	0.109455	0.114876	0.120762	0.126967	0.133408
/A	85.000000	0.107771	0.105399	0.108598	0.114904	0.122482	0.130757	0.139474	0.148494	0.157737
/A	90.000000	0.109993	0.109457	0.115777	0.125041	0.135509	0.146639	0.158186	0.170021	0.182067
/A	95.000000	0.099666	0.098246	0.102457	0.109449	0.117579	0.126333	0.135481	0.144902	0.154522
/A	100.000000	0.090303	0.088209	0.090715	0.095837	0.102031	0.108812	0.115964	0.123372	0.130968
/A	105.000000	0.081760	0.079168	0.080309	0.083903	0.088502	0.093651	0.099148	0.104885	0.110799
/A	110.000000	0.073915	0.070977	0.071044	0.073401	0.076695	0.080503	0.084636	0.088993	0.093514
/A	115.000000	0.066667	0.063512	0.062754	0.064123	0.066362	0.069077	0.072095	0.075321	0.078699
/A	120.000000	0.059931	0.056671	0.055302	0.055896	0.057293	0.059130	0.061245	0.063553	0.066002			
/A	125.000000	0.053636	0.050366	0.048569	0.048571	0.049310	0.050452	0.051850	0.053423	0.055126			
/A	130.000000	0.047720	0.044522	0.042455	0.042023	0.042261	0.042866	0.043703	0.044700	0.045815			
/A	135.000000	0.042129	0.039073	0.036871	0.036141	0.036014	0.036217	0.036628	0.037184	0.037846			
/A	140.000000	0.036815	0.033961	0.031740	0.030828	0.030451	0.030368	0.030470	0.030700	0.031025			
/A	145.000000	0.031737	0.029137	0.026995	0.025998	0.025470	0.025198	0.025089	0.025093	0.025178			
/A	150.000000	0.026857	0.024553	0.022573	0.021575	0.020978	0.020601	0.020363	0.020222	0.020151			
/A	155.000000	0.022141	0.020170	0.018420	0.017488	0.016891	0.016477	0.016179	0.015962	0.015803			
/A	160.000000	0.017559	0.015948	0.014484	0.013674	0.013132	0.012737	0.012434	0.012196	0.012004			
/A	165.000000	0.013080	0.011853	0.010718	0.010073	0.009630	0.009296	0.009032	0.008816	0.008636			
/A	170.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000			
/A	175.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000			
/A	180.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000			
;													
;													
*** TABLE 2													
;										
;sheet thickness										
/S	0.120000									
;										
;bending radii										
/R		0.015000	0.031250	0.062500	0.093750	0.125000	0.156250	0.187500	0.218750	0.250000
;opening angle: ------------------------ correction value x ----------										
/A	0.000000	0.185468	0.136875	0.072829	0.020558	-0.026892	-0.071700	-0.114838	-0.156822	-0.197963
/A	5.000000	0.187816	0.141476	0.080945	0.031862	-0.012534	-0.054362	-0.094565	-0.133647	-0.171908
/A	10.000000	0.190164	0.146076	0.089061	0.043166	0.001824	-0.037023	-0.074291	-0.110471	-0.145854
/A	15.000000	0.192513	0.150677	0.097176	0.054470	0.016182	-0.019684	-0.054018	-0.087295	-0.119799
/A	20.000000	0.194861	0.155278	0.105292	0.065774	0.030540	-0.002345	-0.033745	-0.064120	-0.093745
/A	25.000000	0.197209	0.159879	0.113408	0.077078	0.044898	0.014994	-0.013471	-0.040944	-0.067690
/A	30.000000	0.199557	0.164479	0.121524	0.088382	0.059257	0.032333	0.006802	-0.017768	-0.041635
/A	35.000000	0.201905	0.169080	0.129640	0.099686	0.073615	0.049672	0.027075	0.005407	-0.015581
/A	40.000000	0.204253	0.173681	0.137756	0.110989	0.087973	0.067011	0.047348	0.028583	0.010474
/A	45.000000	0.206601	0.178281	0.145872	0.122293	0.102331	0.084350	0.067622	0.051758	0.036528
/A	50.000000	0.208949	0.182882	0.153988	0.133597	0.116689	0.101689	0.087895	0.074934	0.062583
/A	55.000000	0.211297	0.187483	0.162103	0.144901	0.131047	0.119027	0.108168	0.098110	0.088637
/A	60.000000	0.213645	0.192083	0.170219	0.156205	0.145405	0.136366	0.128441	0.121285	0.114692
/A	65.000000	0.215994	0.196684	0.178335	0.167509	0.159763	0.153705	0.148715	0.144461	0.140746
/A	70.000000	0.218342	0.201285	0.186451	0.178813	0.174121	0.171044	0.168988	0.167636	0.166801
/A	75.000000	0.220690	0.205885	0.194567	0.190117	0.188480	0.188383	0.189261	0.190812	0.192855
/A	80.000000	0.223038	0.210486	0.202683	0.201421	0.202838	0.205722	0.209535	0.213988	0.218910
/A	85.000000	0.225386	0.215087	0.210799	0.212725	0.217196	0.223061	0.229808	0.237163	0.244964
/A	90.000000	0.227734	0.219688	0.218914	0.224029	0.231554	0.240400	0.250081	0.260339	0.271019
/A	95.000000	0.207492	0.198978	0.196491	0.199564	0.204914	0.211512	0.218898	0.226829	0.235158
/A	100.000000	0.188987	0.180217	0.176418	0.177852	0.181429	0.186180	0.191674	0.197680	0.204061
/A	105.000000	0.171957	0.163106	0.158336	0.158473	0.160619	0.163865	0.167807	0.172230	0.177004
/A	110.000000	0.156183	0.147403	0.141954	0.141083	0.142088	0.144120	0.146802	0.149932	0.153390
/A	115.000000	0.141484	0.132905	0.127024	0.125396	0.125509	0.126576	0.128246	0.130332	0.132723
/A	120.000000	0.127707	0.119440	0.113342	0.111170	0.110604	0.110919	0.111791	0.113047	0.114585
/A	125.000000	0.114724	0.106864	0.100732	0.098199	0.097139	0.096885	0.097143	0.097752	0.098620
/A	130.000000	0.102422	0.095051	0.089044	0.086307	0.084910	0.084246	0.084046	0.084167	0.084523
/A	135.000000	0.090705	0.083893	0.078145	0.075341	0.073742	0.072803	0.072282	0.072049	0.072027
/A	140.000000	0.079487	0.073295	0.067922	0.065166	0.063481	0.062382	0.061656	0.061185	0.060902
/A	145.000000	0.068694	0.063173	0.058273	0.055663	0.053990	0.052830	0.051996	0.051386	0.050939
/A	150.000000	0.058258	0.053450	0.049106	0.046725	0.045146	0.044009	0.043149	0.042482	0.041955
/A	155.000000	0.048117	0.044059	0.040339	0.038255	0.036840	0.035792	0.034976	0.034320	0.033781
/A	160.000000	0.038216	0.034936	0.031896	0.030164	0.028968	0.028065	0.027348	0.026759	0.026264
/A	165.000000	0.028502	0.026023	0.023706	0.022370	0.021435	0.020721	0.020146	0.019668	0.019259
/A	170.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000
/A	175.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000
/A	180.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000	0.000000
